Internal electrics
replica of the FL5 flasher relay with 3 screw-in terminals and round housing
BN1 to BJ7
alternatively flasher unit 3083 can be used
Required: 1
replica of the FL5 flasher relay with 3 Lucar terminals and round housing
BJ8
Required: 1
FL5 flasher relay with 3 terminals and round housing
BN1 to BJ8
Required: 1
stop light and rear indicator. Reproduction of the Lucas type DB10 with modern electronics and 8 screw terminals
BN1, BN2, BN4, BN6, BN7, BT7 and BJ7 (1953-63) plus BJ8 to 31335 (1963-65) - not for German and Swedish BN4 from 68960, BN6, BN7, BT7, BJ7 and BJ8. These models have separate indicator lamps but no cut-off relay fitted
Required: 1
BN1 to BJ7, BJ8 to 31335. Not for German and Swedish BN6, BN7, BT7 and BJ7 models.
Required: 3
flasher relay retaining
BN1 to BJ7, BJ8 to 31335. Not for German and Swedish BN6, BN7, BT7 and BJ7 models.
Required: 3
SB40 type with 4 screw terminals - overdrive, starter motor, ignition, horn, alternator and heater motor
BN1 to BJ8
Required: 1
6RA type with 4 Lucar terminals - overdrive, starter motor, ignition, horn, alternator and heater motor
BJ8 (1963-68)
Required: 1
6RA type with 4 Lucar terminals - overdrive, starter motor, ignition, horn, alternator and heater motor
BJ8 (1963-68)
Required: 1
use 318284
BJ8
Required: 1
on kick-down switch
Required: 1
Required: 1
kick-down link
Required: 1
2 fuse variant with 5 screw-in terminals. SF6 type without cover
BN1 to BJ7
Required: 1
25 Ampere with 32 mm overall length and 6.2 mm diameter. Glass type
Required: 1
35 Ampere with 32 mm overall length and 6.2 mm diameter. Glass type
Required: 1
50 Ampere with 32 mm overall length and 6.2 mm diameter. Glass type
Required: 1
50 Ampere with 32 mm overall length and 6.2 mm diameter. Packet of five glass type fuses
Required: 1
25 Ampere with 32 mm overall length and 6.2 mm diameter. Packet of five glass type fuses
Required: 1
35 Ampere with 32 mm overall length and 6.2 mm diameter. Packet of five glass type fuses
Required: 1
reproduction of the Lucas 4FJ type for 2 fuses - variant with lucar terminals
BJ8 (1963-68)
Required: 1
4FJ type for 2 fuses - variant with lucar terminals
BJ8 (1963-68)
Required: 1
low note, Lucas HF.1748 type with 2 terminals. 12 volt - reconditioned, in exchange
BN1 to BN7 and BT7
alternatively horn 2821 can be used
Required: 1
high note, Lucas HF.1748 type with 2 terminals. 12 volt - reconditioned, in exchange
BN1 to BN7 and BT7
alternatively you can use horn 2820
Required: 1
horn
BN1 to BN7 and BT7
Required: 2
low note - reproduction of Lucas 9H windtone horn with two terminals. 12 volt
BJ7 and BJ8 - can also be used for all earlier models
Required: 1
high note - reproduction of Lucas 9H windtone horn with two terminals. 12 volt
BJ7 and BJ8 - can also be used for all earlier models
Required: 1
horn
BJ7 and BJ8 - can also be used for all earlier models
Required: 2
BJ7 and BJ8 - can also be used for all earlier models
Required: 4
BJ7 and BJ8 - can also be used for all earlier models
Required: 4
BJ7 and BJ8
can also be used for all earlier models
Required: 4
headlamps
BN1
alternatively switch 8217 can be used
Required: 1
headlamps - round FS22/1 type with screw-in terminals
BN2 to BJ7
Required: 1
headlamps - square 103SA type with lucar terminals
BJ8
Required: 1
starter motor. ST2 type with push button
BN1 to BJ7 - with starter button
Required: 1
for starter button
BN1 to BJ7 - with starter button
Required: 1
control box cover - sandblasted and painted silver
BN1 to BJ7
Required: 1
BN1 to BJ7
Required: 1
for C39 and C40 dynamo. RB106 type with 5 screw-in terminals
BN1 to BJ7
Required: 1
for Lucas C42, C47 and C48 dynamo. RB340 type with 30 ampere
BJ8 (1963-68)
Required: 1
