Cylinder head MKII
rear crankshaft cover to cylinder block - diameter: 5/16"
Required: 16
on studs
Original 'D' washer no longer available. Use washer 212193 with spring washer 212194
Required: 16
on studs
Original 'D' washer no longer available. Use washer 212193 with spring washer 212194
Required: 16
fixing cylinder head to front timing cover and cylinder block
Required: 4
fixing cylinder head to front timing cover and cylinder block
Required: 4
fixing cylinder head to front timing cover and cylinder block
Required: 4
inlet and exhaust manifold. Set with 34 short stainless steel studs
Required: 1
exhaust manifold, length: 1.3/4" - for gearbox breather
Required: 2
7/16" - galvanised D-shaped washer for cylinder head dome nut
7/16" - galvanised 3.4 mm thick washer for cylinder head dome nut
made of chrome-nickel-magnesium steel with nitrided surface. Diameter: 41.3 mm
Mark II 3.4, 3.8 und 340 (1959-69)
Required: 6
made of chrome-nickel-magnesium steel with nitrided surface. Diameter: 41.3 mm
Required: 6
set with one inner and one outer spring
Required: 6
top, for inlet valve and exhaust valve - aftermarket
Required: 12
inlet valve - bronze valve guide with 0.502" outside diameter and 1.866" length
Required: 6
inlet valve +0.003" (1st oversize). Steel type
Required: 6
inlet valve - bronze valve guide with 0.507" outside diameter and 1.866" length
Required: 6
inlet valve, 2nd oversize with 12.85 mm outer diameter and 47.41 mm length. Steel type
Required: 6
inlet valve - bronze valve guide with 0.504" outside diameter and 1.866" length
Required: 6
inlet valve, 3rd oversize with 12.95 mm outer diameter. Steel type
Required: 6
inlet valve - bronze valve guide with 0.510" outside diameter and 1.866" length
Required: 6
exhaust valve, 1st oversize with 12.83 mm outer diameter. Steel type
Required: 6
exhaust valve - bronze valve guide with 0.506" outside diameter and 1.957" length
Required: 6
exhaust valve, 2nd oversize with 12.88 mm outer diameter. Steel type
Required: 6
exhaust valve - bronze valve guide with 0.507" outside diameter and 1.957" length
Required: 6
exhaust valve, 3rd oversize with 12.95 mm outer diameter. Steel type
Required: 6
exhaust valve - bronze valve guide with 0.510" outside diameter and 1.957" length
Required: 6
inlet valve. Hardened version for lead free applications. Dimensions: OD = 1.85", ID = 1.437", H = 0.394"
3.4 and 340 engines
Required: 6
inlet valve. Hardened version for lead free applications. Dimensions: OD = 1.88", ID = 1.38", H = 0.43"
3.8 engine
Required: 6
exhaust, hardened, semi finished. For lead free applications - dimensions: outer diameter: 42,9 mm inner diameter: 33,45 mm heigth: 6,15 mm
Required: 6
long skirt version with 1.3/8" original diameter and 1" total height
Required: 12
with 1.3/8" original diameter and 7/8" total height
Required: 12
aftermarket with 1.3/8" original diameter and 7/8" total height
Required: 12
for Jaguar XK6 engines and 6.0 V12 engines (diameter 17.44 mm <> 0.6126 inch)
Required: 1
tachometer - on inlet camshaft
Required: 1
polished aluminium - set of two.For cars fitted with electric tachometer. Features: Recess on LH exhaust cover: 29 mm, recess on RH inlet cover: 46 mm
Required: 1
raw aluminium - set of two.For cars fitted with electric tachometer. Features: Recess on LH exhaust cover: 29 mm, recess on RH inlet cover: 46 mm
Required: 1
RH - polished aluminium. Feature: slot for electric tachometer drive
Required: 1
for LH smooth rocker cover. Made of polished aluminium with 68 mm diameter
Early models with smooth rocker cover
Required: 1
oil filler cap
Early models with smooth rocker cover
Required: 1
for left rocker cover
Later models with ripped rocker cover
Required: 1
oil filler cap
Later models with ripped rocker cover
Required: 1
engine breather
Very early models - not breathing thru' air cleaner. Quote engine no.
Required: 1
engine breather air hose
Very early models - not breathing thru' air cleaner. Quote engine no.
Required: 2
engine breather - 90° angled
Models breathing through air cleaner. Some earlier models are fitted with an elbow hose for the breather housing whilst later models have a straight hose, repeated at the air cleaner end. Both are of a similar diameter. Qute engine no.
Required: 2
engine breather - 78 cm long
Models breathing through air cleaner. Some earlier models are fitted with an elbow hose for the breather housing whilst later models have a straight hose, repeated at the air cleaner end. Both are of a similar diameter. Qute engine no.
Required: 2
engine breather hose
Models breathing through air cleaner. Some earlier models are fitted with an elbow hose for the breather housing whilst later models have a straight hose, repeated at the air cleaner end. Both are of a similar diameter. Qute engine no.
Required: 4
made from high quality composite material. Bore size: 86.00 mm + 0.5 mm, thickness: 0.35", built in thickness: 0.33"
Mark II: 3.4 and 340
Required: 1
made from high quality composite material. Bore size: 88.50 mm, Thickness: 0.35", built in thickness: 0.33"
Mark II: 3.8
Required: 1
'full race', made from high quality composite material. Bore size: 90.5 mm, thickness: 0.64", built in thickness: 0.61"
Mark II: 3.8
Required: 1
made from sheet metal
Mark II: 2.4, 3.4, 240 and 340
Required: 1
down pipe to exhaust manifold - inner diameter: 51 mm, total height: 12.5 mm
Mark II (1961-69): 2.4 from 112355 and 126735, 3.4 from 158296 and 177750, 3.8 from 230001 and 219614 plus all 240 and 340 models
Required: 2
down pipe to exhaust manifold - inner diameter: 51 mm, total height: 12.5 mm
Mark II (1961-69): 2.4 from 112355 and 126735, 3.4 from 158296 and 177750, 3.8 from 230001 and 219614 plus all 240 and 340 models
Required: 2
front. Please note: no guarantee for enamel
3.4 and 3.8
Required: 1
front. Please note: no guarantee for enamel
2.4 and 240
Required: 1
rear. Please note: no guarantee for enamel
3.4 and 3.8
Required: 1
rear. Please note: no guarantee for enamel
2.4 and 240
Required: 1
in black, for Lucas DMBZ6A and 22D6 distributors. Identified by acorn nuts to fix ignition leads
Required: 1
ignition lead - thickness: 0.25"
3.4/3.8 - original for later models
Required: 2
ignition lead - thickness: 0.13"
3.4/3.8 - original for later models
Required: 3
90° angled - plastic reproduction with Champion lettering
Required: 6
made in red vulcanised fibreboard with the correct rivets and brackets
Required: 6
quick release type, polished aluminium. Monza style with 65 mm diameter
Required: 1
stainless steel with 2" diameter - 4 piece set for RHD models. This kit will come with adaptor pipes to link to the standard system
Mark II 3.4, 340 and 3.8 RHD models (1959-69)
Required: 1
stainless steel with 2" diameter - 4 piece set for LHD models. This kit will come with adaptor pipes to link to the standard system
Mark II 3.4, 340 and 3.8 LHD models (1959-69)
Required: 1
