Wheel bearing and drive shaft
RH rear - feature: for Rover type axle with haf shaft with 10 splines, length: 67 cm
Series II and IIA (1958-71) plus 88" Series III to June 1980
Required: 1
RH rear - feature: for ENV type axle with haf shaft with 10 splines to inner end and 24 splines to outer end, overall length: 32.9"
Series II and IIA (1958-71)
Required: 1
RH rear - feature: for Salisbury type axle with haf shaft with 24 splines
88" Series III from July 1980
Required: 1
RH rear - feature: for Salisbury type axle with haf shaft with 24 splines
109" Series III (1971-85)
Required: 1
LH rear - feature: for Rover type axle with haf shaft with 10 splines, length: 88.8 cm
Series II and IIA (1958-71) plus 88" Series III to June 1980
Required: 1
LH rear - feature: for ENV type axle with haf shaft with 10 splines to inner end and 24 splines to outer end, overall length: 32.9"
Series II and IIA (1958-71)
Required: 1
LH rear - feature: for Salisbury type axle with haf shaft with 24 splines
88" Series III from July 1980
Required: 1
LH rear - feature: for Salisbury type axle with haf shaft with 24 splines
109" Series III (1971-85)
Required: 1
rear axle
Series II and IIA (1958-71) plus Series III to September 1980 except 109" 3.5 V8 models
Required: 2
rear axle
109 V8 models to September 1980
109 V8 models
Required: 2
rear axle
Series III including 3.5 V8 models from October 1980
Required: 2
wheel bearing
Series II, IIA and early Series III 4- and 6-cylinder models (1958 to October 1980)
Required: 2
wheel bearing
Series III 4- and 6-cylinder models from October 1980 plus alle Series III V8 (1979-85)
Required: 2
wheel bearing
All models except 109 V8 to September 1980
Required: 2
rear suspension - inner bearing
Series II, IIA and early Series III 4- and 6-cylinder models (1958 to October 1980)
Required: 2
rear suspension - inner bearing
Series III 4- and 6-cylinder models from October 1980 plus alle Series III V8 (1979-85)
Required: 2
with wheel studs
Serie II, IIA and Serie III to September 1980 except 109 V8
Required: 2
Serie III from October 1980, 109 V8 all models
Required: 2
front and rear suspension - outer bearing
Series II, IIA and early Series III 4- and 6-cylinder models (1958 to october 1980)
Required: 2
rear suspension - outer bearing
Series III 4- and 6-cylinder models from October 1980 plus alle Series III V8 (1979-85)
Required: 2
rear
Serie II, IIA Rover axle, Serie III 88 to Juni 1980
Identify by: 10 splines
Required: 2
rear
Serie III 109 to September 1983, 88 Serie III from July 1980 to September 1983
Required: 2
rear
Serie III from October 1983 except 109 V8
Required: 2
Serie II, IIA Rover axle, Serie III 88 to Juni 1980
Required: 2
drive flange
Series II and IIA with Rover axle, 88" Series III to June 1980
Required: 2
Series II, IIA with Rover axle, Serie III 88 to Juni 1980
Required: 2
Serie II, IIA Rover-axle, Serie III 88 to Juni 1980
Required: 2
drive flange
Serie II, IIA ENV axle, Serie III 109 models and 88 models from July 1980 to September 1983
Required: 2
Serie II, IIA ENV axle, Serie III 109 models and 88 models from July 1980
Required: 2
with 9/16" BSF thread - screw in type
Series II all models and Series IIa to suffix "G"
Required: 10
with 9/16" BSF thread - press fit type
Series II and Series IIa to suffix "G"
Required: 10
with M16 x 1.5 thread and 41.8 mm total length - press fit type
Serie IIA from suffix "H" and Serie III
Required: 10
rear
Series II, IIA and early Series III 4- and 6-cylinder models (1958 to October 1980)
Required: 2
rear
Series III 4- and 6-cylinder models from October 1980 plus alle Series III V8 (1979-85)
Required: 2