Ignition
with push-in HT lead terminal and approx. 2.8 Ohm primary resistance. Non ballasted type
upto approx. 1982
for use without ballast resistor
Required: 1
with push-in HT lead terminal and approx. 2.8 Ohm primary resistance. Non ballasted type
upto approx. 1982
for use without ballast resistor
Required: 1
with push-in HT lead terminal and approx. 1.4 Ohm primary resistance. Ballasted type
approx. 1982 on upto 1275 cc 1990 on
for use with ballast resistor. Ballast resistor is integrated in loom (white/pink wire)
Required: 1
with push-in HT lead terminal and approx. 1.4 Ohm primary resistance. Ballasted type
approx. 1982 on upto 1275 cc 1990 on
for use with ballast resistor. Ballast resistor is integrated in loom (white/pink wire)
Required: 1
for constant energy ignition system, primary resistance: 0.6 Ohm
1275 cc models with SU-HIF44 carburettor (1990-92) and 1.3 Spi (1992-97)
for use with ballast resistor. Ballast resistor is integrated in loom (white/pink wire)
Required: 1
retaining ignition coil to bracket dynamo
early cars
Required: 2
retaining ignition coil to bracket dynamo
early cars
Required: 2
retaining ignition coil to mounting bracket
Required: 2
for Lucas DM2, DM2P4, 23D4 and 25D4 distributor with side entry cap
1959 upto 1968
Required: 1
for Lucas 25D4 and 45D4 distributor with top entry cap
1968 upto 1997
Required: 1
for Lucas 25D4, 45D4, 59D4 and 65D4 plus Ducellier distributor with top entry cap. Identify by push fit ignition leads. HT lead set with 8 mm silicone jacket in black
from 1968 to 2000
Required: 1
for Lucas 25D4, 45D4, 59D4 and 65D4 plus Ducellier distributor with top entry cap. Identify by push fit ignition leads. HT lead set with 8 mm silicone jacket in blue
from 1968 to 2000
Required: 1
retaining ignition coil to mounting plate
1.3 Mpi (1997-2000)
Required: 1
for ignition coil pack - black
1.3 Mpi (1997-2000)
Required: 1
for ignition coil pack - stainless steel, polished with screws
1.3 Mpi (1997-2000)
Required: 1
retaining mounting plate to engine block
1.3 Mpi (1997-2000)
Required: 3
for BTDC signal - fitted to bell housing and the sensor head protrudes into a groove in the flywheel
1.3 Mpi (1997-2000)
Required: 1
BP6
848 cc, 998 cc upto 1986, 1098 cc, 1275 cc
alternative for spark plug 14678
Required: 4
BPR6 resistor
848 cc, 998 cc upto 1986, 1098 cc, 1275 cc
alternative for spark plug 500531
Required: 4
N9
848 cc, 998 cc upto 1986, 1098 cc, 1275 cc
alternative for spark plug 6915
Required: 4
RN9 resistor
848 cc, 998 cc upto 1986, 1098 cc, 1275 cc
alternative for spark plug 373919
Required: 4
998 cc 1987 upto 09/1989
alternative for spark plug 204835
Required: 4
N11
998 cc 1987 to 09/1989
alternative for spark plug 12041
Required: 4
BP4 resistor
998 cc 09/1989 upto 1992
alternative for spark plug 325944
Required: 4
RN12 resistor
998 cc 09/1989 upto 1992
alternative for spark plug 307109
Required: 4
BPR6 resistor
1275 cc carburettor 1990 upto 1992, 1275 cc Single Point Injection 1992 on
Required: 4
for ignition - large
Clubman
Required: 1
for ignition - large
998 cc upto 1992
Required: 1
for ignition - large
1275 cc carburettor 1990 upto 1992
Required: 1
for ignition - large
1275 cc injection 1992 on
Required: 1
for ignition - large
cars with automatic gearbox upto (V) 338941
Required: 1
for ignition - large
cars with automatic gearbox (V) 338942 on
Required: 1
for splash shield top
fitted on rocker cover bolts
replaces earlier one peace rype
Required: 2
for splash shield bottom
fitted on bolts engine to gearbox
replaces earlier two peace type
Required: 1
€39.00
