Differential - manual gearbox
A series
if thrustblock 306641 used
Required: 1
A plus series
if thrustblock 306641 is omitted
Required: 1
differential
A series
if differential case 298519 is used
Required: 1
0.035", pinion differential
A series
if differential case 298519 is used
Required: 2
bronce, with locating lip
A plus series
if differential case 298520 is used
Required: 2
for differential pinion
with lubrication grooves for planet gears
Required: 1
uprated, for differential pinion
alternative for pin 203189 or 305060
Required: 1
for differential overhaul - content: 1x Differential pin, 2x Planet gears, 2x Thrust washers, 1x Roll pin
Required: 1
64 teeth, final drive 3.76:1
A series
for 17 teeth pinion
Required: 1
62 teeth, final drive 3.44:1
A series
for 18 teeth pinion
Required: 1
62 teeth, final drive 3.44:1
A plus series
for 18 teeth pinion
Required: 1
61 teeth, final drive 3.21:1
A plus series
for 19 teeth pinion
Required: 1
59 teeth, final drive 3.105:1
A plus series
for 19 teeth pinion
Required: 1
59 teeth, final drive 2.95:1
A plus series
for 20 teeth pinion
Required: 1
3.105:1, Crownwheel & Pinion 59 x 19 teeth
A-plus series
2.95:1, Crownwheel & Pinion 59 x 20 teeth
A-plus series
for differential output shaft bearing, thickness: 0.002" / 0.0508 mm
for differential output shaft bearing, thickness: 0.003" / 0.0762 mm
for differential output shaft bearing, thickness: 0.006" / 0.1524 mm
for differential output shaft bearing, thickness: 0.010" / 0.2540 mm
output shaft - used item
models with 'magic wand' or 'remote' gearbox (1959-73)
Required: 2
output shaft
models with 'magic wand' or 'remote' gearbox (1959-73)
Required: 2
output shaft
models with 'rod change' gearbox (1973-2000)
Required: 1
cover differential output shaft
for rubbercoupling type
Required: 2
cover differential output shaft
for rubbercoupling type
Required: 2
20 teeth on shaft
early cone synchromesh gear box
for rubbercoupling type
Required: 2
21 teeth on shaft
for rubbercoupling type
Required: 2
20 teeth
early cone synchromesh gear box
for rubbercoupling type
Required: 2
21 teeth
for rubbercoupling type
Required: 2
output flange to shaft
for rubbercoupling type
Required: 2
output flange to shaft
for rubbercoupling type
Required: 2
self locking
alternative for slotted nut 16904 and split pin 7467
Required: 2
to December 1972
Required: 2
consists from one coupling, four U bolts with nuts, for one car side
to December 1972
Required: 2
heavy duty version with nylon bushes and neddle bearings. Supplied including U-bolts and nuts
to December 1972
Required: 2
output shaft
for Hardy Spicer type
Required: 2
output shaft, right hand
"Rod" type gearbox
for Hardy Spicer type
Required: 1
for differential output shaft cover
models with Hardy Spicer type drove flange
Required: 2
cover differential output shaft
Cooper S
for Hardy Spicer type
Required: 2
for Hardy Spicer type
Required: 2
for output shaft
for Hardy Spicer type
Required: 4
models with Hardy Spicer type drove flange
Required: 2
output flange to shaft
for Hardy Spicer type
Required: 2
output shaft
models with 'magic wand' or 'remote' gearbox with pot joint (1959-73)
Required: 2
output shaft
models with 'rod change' gearbox with pot joint (1973-2000)
Required: 2
cover differential output shaft
for pot joint type
Required: 2
differential - for constant velocity joint
A-series, replaced by part no. 306639
Required: 2
differential - for constant velocity joint
A-Series and A-plus Series (1959-2000)
Required: 2
for differential output shaft on models with constant velocity joint
Required: 2
gear box side
for pot joint type
Required: 2
