Switches and steering lock - TR5/250, TR6 to September 1972
in red with chrome bezel - diameter: 7/8". Handbrake, hazard warning, choke and heated rear window
LHD models
Required: 2
for bulbs with BA9s bayonet base - variant with screw connection for single wire
LHD models
Required: 2
windscreen wiper - identify by 3 terminals
TR5, TR250
Required: 1
windscreen wiper - identify by 4 terminals
TR6
Required: 1
for 'Clear Hooters' wiper switch
Required: 1
windscreen wiper - identify by 4 terminals
May replace 'Clear Hooters' switches
Required: 1
wiper - single speed
Required: 1
for 'Clear Hooters' windscreen washer switch
Required: 1
windscreen washer
May replace 'Clear Hooters' switch
Required: 1
switch to dashboard
Required: 2
Required: 4
hazard warning - identify by 4 terminals
LHD models: TR5/250, TR6 Carburettor to CC67893, TR6 P.I. to CP54584
Required: 1
switch to dashboard
LHD models: TR5/250, TR6 Carburettor to CC67893, TR6 P.I. to CP54584
Required: 1
LHD models: TR5/250, TR6 Carburettor to CC67893, TR6 P.I. to CP54584
Required: 2
switch to dashboard
TR6 Carburettor from CC75001, TR6 P.I. from CP75001. May replace all earlier hazard warning switches
Required: 1
TR6 Carburettor from CC75001, TR6 P.I. from CP75001. May replace all earlier hazard warning switches
Required: 2
hazard warning - identify by 6 terminals
TR6 Carburettor from CC75001, TR6 P.I. from CP75001. May replace all earlier hazard warning switches
Required: 1
fasten seat belts
LHD models: TR6 Carburettor from CC75001, TR6 P.I. from CP75001
Required: 1
for warning lamp
LHD models: TR6 Carburettor from CC75001, TR6 P.I. from CP75001
Required: 1
rheostat to dashboard rear
Required: 1
Required: 2
rheostat to bracket
Required: 1
rheostat
Required: 1
in knob
Required: 1
rheostat
TR5/250, TR6 Carburettor to CC32142, TR6 P.I. to CP26998
Required: 1
rheostat
TR6 Carburettor from CC50001, TR6 P.I. from CP50001
Required: 1
air distribution control cable - pictorial type
TR5/250, TR6 Carburettor to CC67893, all TR6 P.I.
Required: 1
air distribution cable - written type
TR6 Carburettor from CC75001
Required: 1
heater fan switch
Required: 1
heater fan switch - pictorial type
TR5/250, TR6 Carburettor to CC67893, all TR6 P.I.
Required: 1
heater fan switch - written type
TR6 Carburettor from CC75001
Required: 1
heater fan - two speed. Please note: rated at 10 amps on 12 volt systems
May replace OE push/pull switch
Required: 1
heater control cable - pictorial type
TR5/250, TR6 Carburettor to CC67893, all TR6 P.I.
Required: 1
heater control cable - written type
TR6 Carburettor from CC75001
Required: 1
with barrel and two keys
Models without steering lock: TR5/250, TR6 Carburettor to CC32142, TR6 P.I. to CP26998
Required: 1
ignition switch
Models without steering lock: TR5/250, TR6 Carburettor to CC32142, TR6 P.I. to CP26998
Required: 1
ignition switch
Models without steering lock: TR5/250, TR6 Carburettor to CC32142, TR6 P.I. to CP26998
Required: 1
ignition switch
Models without steering lock: TR5/250, TR6 Carburettor to CC32142, TR6 P.I. to CP26998
Required: 1
ignition switch - with two keys
Models without steering lock: TR5/250, TR6 Carburettor to CC32142, TR6 P.I. to CP26998
Required: 1
blank key with FA code
To identify the correct ignition lock key for your vehicle, add the three-digit combination to your key code to, i. e. FS876
Required: 1
blank key with FS code
To identify the correct ignition lock key for your vehicle, add the three-digit combination to your key code to, i. e. FS876
Required: 1
blank key with FT code
To identify the correct ignition lock key for your vehicle, add the three-digit combination to your key code to, i. e. FS876
Required: 1
longer version with flexible wire, may replace original choke cable - characteristic: knob with 'choke' pictorial. Cable length: 41.3/4" and 49.1/4"
Longer version. May replace original choke cable.
Required: 1
choke cable - pictorial type
TR5/250, TR6 Carburettor to CC67893, all TR6 P.I.
Required: 1
choke cable - written type
TR6 Carburettor from CC75001
Required: 1
12 volt, for positive and negative earthed cars without cut-off relay, complete with fitting instructions
Comes with fitting instructions
Required: 1
master lighting and headlamp flash on LHD models - identified by 4 cables and black handle
TR5 and TR250 (1967-68) • TR6 to August 1971: Carburettor models to CC67893, P.I. models to CP54584
Required: 1
master lighting and headlamp flash on LHD models - identified by 4 cables and chrome handle
TR5 and TR250 (1967-68) • TR6 to August 1971: Carburettor models to CC67893, P.I. models to CP54584
Required: 1
headlamp dip main beam and headlamp flash on LHD models - identified by 5 cables and black handle
TR6 from August 1971 to September 1972: Carburettor models from CC75001 to CC85737, P.I. models from CP75001 to CP77718
Required: 1
master lighting and headlamp flash on RHD models - identified by 4 cables and black handle
TR5 (1967-68) • TR6 to September 1972: P.I. models to CP77718
Required: 1
overdrive on LHD models - identified by 2 cables and black handle
Required: 1
overdrive on RHD models - identified by 2 cables and black handle
Required: 1
with ignition switch assembly. Feature: 7 Lucar connections, no loom. Supplied with 2 keys
All models with steering lock. This type of steering lock may replace all earlier versions
Required: 1
steering lock - 5/16" UNC thread
All models with steering lock. This type of steering lock may replace all earlier versions
Required: 2
steering lock - serial no. LU39415. Characteristic: 35 mm diameter, 7 Lucar connections, no loom
TR6 Carburettor from CC50001, TR6 P.I. from CP50001
Required: 1
headlamps - square 103SA type with lucar terminals
Required: 1
dashboard
TR5/250, TR6 Carburettor to CC32142, TR6 P.I. to CP26998
Required: 1
dashboard
TR6 Carburettor from CC50001 to CC67893, TR6 P.I. from CP50001
Required: 1
