Ball joint, wheel bearing and drive shaft
LH front - identified by 3/8" steering lever studs
Series II (1958-61) pluy Series IIA to February 1962
Richiesto: 1
RH front - identified by 3/8" steering lever studs
Series II (1958-61) pluy Series IIA to February 1962
Richiesto: 1
LH front - identified by 7/16" steering lever studs
Series IIA from February 1962: 88" RHD models from 24101876A, 109" RHD models from 25101786A and 109" LHD models from 25400867A plus all Series III except 109" V8 models (1971-85)
Richiesto: 1
RH front - identified by 7/16" steering lever studs
Series IIA from February 1962: 88" RHD models from 24101876A, 109" RHD models from 25101786A and 109" LHD models from 25400867A plus all Series III except 109" V8 models (1971-85)
Richiesto: 1
LH - identify by 7/16" steering lever bolts
Serie III 109 V8
Identify by: 7/16" steering lever studs
Richiesto: 1
RH - identify by 7/16" steering lever bolts
Serie III 109 V8
Identify by: 7/16" steering lever studs
Richiesto: 1
front drive shaft housing
Serie II, IIA and IIII except 109 V8
Richiesto: 2
front drive shaft housing
109 V8
Richiesto: 2
upper front suspension swivel - thickness: 3.25 mm
Richiesto: 2
swivel - 0.003"
Identify by: 7/16" steering lever studs
swivel - 0.005"
Identify by: 7/16" steering lever studs
swivel - 0.010"
Identify by: 7/16" steering lever studs
swivel - 0.030"
Identify by: 7/16" steering lever studs
front suspention
Identify by: 7/16" steering lever studs
Richiesto: 2
upper swivel pin
Identify by: 7/16" steering lever studs
Richiesto: 8
front suspension swivel housing - identified by 7/16" steering lever studs
Identify by: 7/16" steering lever studs
Richiesto: 8
retainig swivel pin
Identify by: 7/16" steering lever studs
Richiesto: 4
retaining swivel pin an steering lever
Identify by: 7/16" steering lever studs
Richiesto: 4
RH
right hand steering
Identify by: 3/8" steering lever studs
Richiesto: 1
LH
right hand steering
Identify by: 3/8" steering lever studs
Richiesto: 1
RH
left hand steering
Identify by: 3/8" steering lever studs
Richiesto: 1
LH
left hand steering
Identify by: 3/8" steering lever studs
Richiesto: 1
RH
right hand steering
Early models
Richiesto: 1
LH
right hand steering
Early models
Richiesto: 1
RH side - for LHD models
Later Series IIA and early Series III four and six cylinder models with axles with non-pendant type swivels and 7/16" studs
Richiesto: 1
LH side - for LHD models
Later Series IIA and early Series III four and six cylinder models with axles with non-pendant type swivels and 7/16" studs
Richiesto: 1
RH
right hand steering
Late models
Richiesto: 1
LH
right hand steering
Late models
Richiesto: 1
RH
left hand steering
Late models
Richiesto: 1
LH
left hand steering
Late models
Richiesto: 1
RH
Serie III 109 V8 - right hand steering
Richiesto: 1
LH
Serie III 109 V8 - right hand steering
Richiesto: 1
RH
Serie III 109 V8 - left hand steering
Richiesto: 1
LH
Serie III 109 V8 - left hand steering
Richiesto: 1
- lower position
Richiesto: 2
swivel - 0.003"
Identify by: 3/18" steering lever studs
swivel - 0.005"
Identify by: 3/18" steering lever studs
swivel - 0.010"
Identify by: 3/18" steering lever studs
swivel - 0.030"
Identify by: 3/18" steering lever studs
swivel - 0.003"
Identify by: 7/16" steering lever studs
swivel - 0.005"
Identify by: 7/16" steering lever studs
swivel - 0.010"
Identify by: 7/16" steering lever studs
swivel - 0.030"
Identify by: 7/16" steering lever studs
RH
right hand steering
pendant type
Richiesto: 1
LH
right hand steering
pendant type
Richiesto: 1
RH
left hand steering
pendant type
Richiesto: 1
LH
left hand steering
pendant type
Richiesto: 1
front supension, upper - cone and spring type, identified by 3/8" steering lever studs
Richiesto: 2
front supension, upper - cone and spring type, identified by 7/16" steering lever studs
Identify by: 7/16" steering lever studs
Richiesto: 2
retaining steering arm an swivel pin
Pendant type - Identify by: 3/8" steering lever studs
Richiesto: 2
retaining steering arm
Pendant type - Identify by: 3/8" steering lever studs
Richiesto: 6
retaining swivel pin
Identify by: 3/8" steering lever studs
Richiesto: 8
retaining swivel pin
Identify by: 7/16" steering lever studs
Richiesto: 8
front suspension swivel housing - identified by 3/8" steering lever studs
Richiesto: 8
front suspension swivel housing - identified by 7/16" steering lever studs
Richiesto: 8
retaining swivel pin
Identify by: 3/8" steering lever studs
Richiesto: 8
retaining swivel pin
Identify by: 7/16" steering lever studs
Richiesto: 8
front supension, lower - cone and spring 'Pendant' type, identified by 3/8" steering lever studs
Richiesto: 2
retaining swivel pin
Pendant type - Identify by: 3/8" steering lever studs
Richiesto: 8
Serie II,IIA and III to September 1980
Richiesto: 2
stub axle to swivel housing - front suspension
Richiesto: 2
drive shaft
all 88" and 109" Series II and IIA models (1959-71) plus 88" Series III to June 1980
Richiesto: 2
front axle, RH side
Series II, IIA and III except 109" One-ton and V8 models (1958-85)
Richiesto: 1
front axle, LH side
Series II, IIA and III except 109" One-ton and V8 models (1958-85)
Richiesto: 1
drive shaft front axle - sealed type with 75,3 mm span width and 27 mm cup diameter
Richiesto: 2
drive shaft front axle - sealed type with 75,3 mm span width and 27 mm cup diameter
Richiesto: 2
all 88" and 109" Series II and IIA models (1959-71) plus 88" Series III to June 1980
Richiesto: 2
Serie III 109er all, 88er from July to September 1980 and 109 1 Ton
Richiesto: 2
Serie III 109 and 88 from Oktober 1980 onwards except 109 1 Ton
Richiesto: 2
Serie III 109 V8
Richiesto: 2
front drive shaft
Series II, IIA and III (1958-85): all 88" and 109" except 109" V8
Richiesto: 2
front drive shaft
Series III 109" V8 (1979-85)
Richiesto: 2
drive shaft front axle - inner
Richiesto: 2
for bearing
Serie II, IIA und III except 109 V8
Richiesto: 2
retaining axle housing
Serie II, IIA und III except 109 1 Ton and 109 V8
Richiesto: 10
retaining axle housing
Serie III 109 1 Ton and 109 V8
Richiesto: 10
retaining axle housing
Serie II, IIA and III except 109 1 Ton and 109 V8
Richiesto: 2
retaining axle housing
Serie III 109 1 Ton and 109 V8
Richiesto: 2
support ring to drive shaft housing - length: 5/8"
Richiesto: 10
support ring to drive shaft housing - length: 1"
Richiesto: 2
oil seal
109 V8
Richiesto: 2
wheel bearing in front hub
Series II, IIA and early Series III 4- and 6-cylinder models (1958 to October 1980)
Richiesto: 2
wheel bearing in front hub
Series III 4- and 6-cylinder models from October 1980 plus alle Series III V8 (1979-85)
Richiesto: 2
front suspension - inner bearing
Series II, IIA and early Series III 4- and 6-cylinder models (1958 to October 1980)
Richiesto: 2
front suspension - inner bearing
Series III 4- and 6-cylinder models from October 1980 plus alle Series III V8 (1979-85)
Richiesto: 2
with wheel studs
Series II and IIA (1958-71), Series III except V8 models to September 1980
Richiesto: 2
Series III from October 1980 and all V8 models
Richiesto: 2
front and rear suspension - outer bearing
Series II, IIA and early Series III 4- and 6-cylinder models (1958 to october 1980)
Richiesto: 2
front suspension - outer bearing
Series III 4- and 6-cylinder models from October 1980 plus alle Series III V8 (1979-85)
Richiesto: 2
front or rear
Series II, IIA and early Series III 4- and 6-cylinder models (1958 to October 1980)
Richiesto: 2
front
Series III 4- and 6-cylinder models from October 1980 plus alle Series III V8 (1979-85)
Richiesto: 2
with 9/16" BSF thread - screw in type
Series I and II (1948-61), Series IIA to vehicle suffix 'G' (1961-69)
Richiesto: 10
with 9/16" BSF thread - press fit type
Series I and II (1948-61), Series IIA to vehicle suffix 'G' (1961-69)
Richiesto: 10
with M16 x 1.5 thread and 41.8 mm total length - press fit type
Series IIA from vehicle suffix 'G' (1969-71) and all Series III (1971-85)
Richiesto: 10
with 10 splines
Serie II, IIA and III 88 to June 1980
Richiesto: 2
retaining driving flange
Serie II, IIA and III 88 to June 1980
Richiesto: 12
Serie II, IIA and III 88 to June 1980
Richiesto: 12
Serie II, IIA and III 88 to June 1980
Richiesto: 2
drive flange
Serie II, IIA and III 88 to June 1980
Richiesto: 2
drive flange
Serie II, IIA and III 88 to June 1980
Richiesto: 2
Serie II, IIA and III 88 to June 1980
Richiesto: 2
Serie II, IIA and III 88 to June 1980
Richiesto: 2
with 24 splines
109" Series III except V8 models to September 1983, 88" Series III from July 1980 to September 1983
Richiesto: 2
Series III except V8 models from October 1983
Richiesto: 2
retaining driving flange
Serie III 109, 88 Serie III from July 1980 except 109 V8
Richiesto: 12
Serie III 109, 88 Serie III from July 1980 except 109 V8
Richiesto: 12
drive flange
Serie III from October 1983 except 109 V8
Richiesto: 2
drive flange, front suspension
109" Series III except V8 models (1971-85) plus all 88" Series III from July 1980 onwards
Richiesto: 2
Serie III 109, 88 Serie III from July 1980 except 109 V8
Richiesto: 2
Serie III 109, 88 Serie III from July 1980 except 109 V8
Richiesto: 2
Serie III 109, 88 Serie III from July 1980 except 109 V8
Richiesto: 2
front hub
Serie III 109 to September 1983, 88 Serie III from July 1980 to September 1983
Richiesto: 2
front hub
Serie III from October 1983 except 109 V8
Richiesto: 2
with 24 splines
109" Series III V8 models to September 1983
Richiesto: 2
Series III V8 models from October 1983
Richiesto: 2
drive flange
109er V8 to September 1983
Richiesto: 2
0.044"
109 V8
Richiesto: 2
0.050"
109 V8
Richiesto: 2
0.056"
109 V8
Richiesto: 2
0.062"
109 V8
Richiesto: 2
0.068"
109 V8
Richiesto: 2
0.074"
109 V8
Richiesto: 2
0.080"
109 V8
Richiesto: 2
0.086"
109 V8
Richiesto: 2
0.092"
109 V8
Richiesto: 2
0.098"
109 V8
Richiesto: 2
0.104"
109 V8
Richiesto: 2
0.110"
109 V8
Richiesto: 2
0.116"
109 V8
Richiesto: 2
0.122"
109 V8
Richiesto: 2
front hub
109 V8 to September 1983
Richiesto: 2
front hub
109 V8 from October 1983
Richiesto: 2
