Starter motor
M418G 'bomb type' - reconditioned, in exchange. Identified by a 91 tooth ring gear shrunk onto the flywheel
TR2 and TR3, TR3A to TS50000 (1953-59)
Benodigd: 1
for Lucas starter motor M45G and M418G. Supplied in pairs
TR2, TR3, TR3A to TS50000
Benodigd: 2
commutator end bracket
TR2, TR3, TR3A to TS50000
Benodigd: 1
commutator end bracket, oversize type for worn cast shafts
TR2, TR3, TR3A to TS50000
Benodigd: 1
armature shaft
TR2, TR3, TR3A to TS50000
Benodigd: 1
drive end bracket
TR2, TR3, TR3A to TS50000
Benodigd: 1
drive end bracket, oversize type for worn cast shafts
TR2, TR3, TR3A to TS50000
Benodigd: 1
through brackets
TR2, TR3, TR3A to TS50000
Benodigd: 2
for starter pinion
TR2, TR3, TR3A to TS50000
Benodigd: 1
with 9 teeth
TR2, TR3, TR3A to TS50000
Benodigd: 1
starter motor
TR2, TR3, TR3A to TS50000
Benodigd: 1
M418G long type - reconditioned, in exchange. For vehicles with a 90 tooth ring gear bolted to the flywheel
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
for genuine M418G type starter motor
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
for Lucas starter motor M45G and M418G. Supplied in pairs
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 2
for replacement 2M100 type starter motor
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 2
brush tension
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
commutator end
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
commutator end bracket
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
commutator end bracket, oversize type for worn cast shafts
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
armature shaft
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
drive end
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
drive end bracket
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
drive end bracket, oversize type for worn cast shafts
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
through brackets
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 2
securing band cover
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
with 10 teeth
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
for starter pinion - supplied without thrust washers
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
starter pinion
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
starter motor
TR3A from TS50001, TR3B, TR4 and TR4A
Benodigd: 1
on the armature shaft at Lucas starter motors
TR3A from TS50001, TR3B, TR4 und TR4A - 2M100 starter motor armature shaft with thread
Benodigd: 1
on nut
TR3A from TS50001, TR3B, TR4 und TR4A - 2M100 starter motor armature shaft with thread
Benodigd: 1
with cup washer
TR3A from TS50001, TR3B, TR4 and TR4A -M418G starter motor armature shaft without thread
Benodigd: 1
for adjusting starter motors with 127 mm hole spacing, height: 2 mm
starter motor to gearbox
TR2, TR3, TR3A, TR3B and early TR4.
Identify by 11 mm gearbox mounting flange
Benodigd: 2
starter motor to gearbox
late TR4, TR4A.
Identify by 14 mm gearbox mounting flange
Benodigd: 2
